Multi-tech-systems MT2834BL Instrukcja Użytkownika Strona 61
- Strona / 119
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
61
Chapter 6 - S-Registers
Multi-Tech Systems, Inc. MT2834BA/BL Series User Guide
S9
Carrier Detect Response Time
Unit: 100 mSec.
Range: 1-255
Default: 6
Description: S9 sets the time delay between when the modem first detects a valid incoming
carrier signal and when the modem turns on its Carrier Detect circuit. The default
setting is 600 milliseconds, or six units of 100 mSec each (Decimal 6). S9 may be set
for up to 25.5 seconds.
S10
Carrier Loss Disconnect Delay Time
Unit: 100 mSec.
Range: 0-255
Default: 7
Description: S10 sets the time a carrier signal must be lost before the modem disconnects. The
default setting is 700 mSec, or seven units (Decimal 7) of 100 mSec. Maximum delay
is 25.4 seconds (Decimal 254). Setting the S10 value to 255 causes the modem to
not disconnect with loss of carrier. (This S-Register applies at speeds of 2400 bps
and less.)
S11
Tone Dialing: Tone Spacing and Duration
Unit: 1 mSec.
Range: 1-255, 80-255*
Default: 70, 80*
Description: S11 sets the speed of tone dialing (spacing and tone duration times). The default
value is 70 units (Decimal 7) or 80 units, where each unit is one mSec, meaning that
each tone is on for 70 mSec with a 70 mSec pause between each.
The minimum S11 value allowed by most telephone systems is 50 mSec (50 units).
Very few telephone systems can handle anything faster than that. The maximum S11
value is 255 mSec (255 units).
S13
Remote Configuration Escape Character
Unit: ASCII Character
Range: 0-127
Default: 37 (%)
Description: S13 defines the remote configuration escape character (which becomes your
modem’s remote configuration character). The default is three percent symbols
(%%%). When the S13 character is entered three consecutive times from a remotely
connected site, your modem responds with its Remote Configuration procedure.
* Value for International and DOC units
** Value for International units only
- MT2834BA/MT2834BL Series 1
- Intelligent Data/Fax Modems 1
- User Guide 1
- Contents 3
- 1.1 Introduction 6
- 1.2 How To Use This Manual 6
- 1.3 Modem Features 7
- 1.4 Fax Features 8
- 1.5 Technical Specifications 9
- 1.6 Power 10
- 1.7 Modem LED Indicators 11
- 1.8 Controls on PC Board 12
- 2.2 Installation 14
- 2.2.1 Safety Warnings 14
- 2.2.2 Installation Procedure 14
- Figure 2-2. BL Connections 15
- 3.1 Introduction 18
- 3.2 Configuring Your Software 18
- 3.3 PC Initialization Strings 18
- 3.3.2 Other Parameters 19
- 3.5 Modem Basics 20
- 3.5.1 Simple Operations 20
- 4.1 Introduction 22
- 4.2 Dialing/On-Line/Answering 22
- 4.6 Dial-Up Operation 24
- 4.7 Manual Call Origination 24
- 4.8 Automatic Answering 25
- 4.9 Manual Answering 25
- 4.10 Handshaking Details 26
- 4.11 Call Termination 26
- Chapter 5 - Command Mode 27
- 5.1 Introduction 28
- 5.1.1 AT Command Editing 28
- 5.1.2 Functional Modes 28
- 5.2 Summary of AT Commands 29
- 5.3 Result Codes 32
- 5.4 Dialing Commands 33
- 5.4.2 Dial Modifier Commands 34
- Quiet Answer @ 36
- Storing Phone Numbers D...N 37
- Number Linking NN 37
- Modem Reset Z 38
- Unix UUCP Spoofing $SP 39
- Bell/V.21 Tone B 42
- Auto Speed Detect #A 43
- Carrier Detect Control &C 44
- CTS Control &R 44
- Data Set Ready Control &S 45
- Normal Mode &E0 46
- Auto-Reliable Mode &E1 46
- Reliable Mode &E2 46
- V.42 Mode Select #L 47
- Auto-Reliable Buffering $A 47
- Retransmit Count $R 48
- 5.4.9 Flow Control Commands 49
- Xon/Xoff Pass-Through &E7 50
- Send Xon/Xoff Characters #X 50
- Maximum Block Size &BS 51
- Parity Selection #P 51
- Through and Pacing Commands 52
- Speed Conversion $BA 53
- Modem Baud Rate $MB 53
- Serial Port Baud Rate $SB 54
- Help Screens $H 55
- Inquiry for Product Code I 55
- Listing S-Register Values L6 55
- Off Hook H 56
- BREAK AT<CR> 56
- 5.4.13 Line Probe Commands 57
- Chapter 6 - S-Registers 58
- 6.1 Introduction 59
- 7.1 Introduction 69
- Configuration 70
- Change LOGIN Password #I 74
- Change SETUP Password #S 74
- Callback Time Delay (S15) 75
- Callback Attempts (S16) 75
- Local Inactivity Timer (S29) 75
- 8.1 Introduction 77
- 8.3 Speaker Volume Control 83
- DIP-Switches 84
- DIP Switches #13-14 85
- 9.1 Introduction 87
- 9.4 Replacement Parts 89
- 9.5 Technical Support 89
- 9.6 Internet Sites 89
- Appendixes 90
- Upgrade Overview 91
- Appendix B - Troubleshooting 94
- I Am Losing Data 97
- *Factory Default 100
- Password Command Summary 106
- V.25bis Commands 106
- Delayed and Forbidden Numbers 107
- V.25bis Operation 107
- V.25bis Mode AT Commands 108
- V.25bis AT Commands 109
- DTR Dialing ($D) Command 110
- 25-PIN DTE 113
- Connector 113
- 25-PIN DCE 113
- FCC Part 68 Telecom 114
- Canadian Limitations Notice 115
- South African Notice 116
Powiązane produkty i podręczniki dla Sprzęt komputerowy Multi-tech-systems MT2834BL
(2 strony)Behringer Europower PMP960M manuels
Manuels d'utilisation et guides de l'utilisateur pour Mélangeurs Behringer Europower PMP960M.
Nous fournissons des manuels en pdf 2 Behringer Europower PMP960M à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji