Multi-Tech Systems BA-Series Instrukcja Użytkownika Strona 63
- Strona / 109
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
63
Chapter 6 - Callback Security and Remote Configuration
Change SETUP Password #S
The default SETUP password for your modem is
"SMODEMSETUP"
. If you choose to activate
callback security, you should change the SETUP password using this command in the following
format:
AT#Stttttttttt<CR> (where
tttttttttt
is the current SETUP password). Your modem will respond with
"OK"
, indicating that you can enter the new SETUP password as follows:
AT#s=uuuuuuuuuu<CR>
You can select any combination of keyboard characters (upper/lower case sensitive) between six
and ten characters long.
Erase Callback Password #RCBNxx
This command erases the single callback password specified by
xx
(0 through 29).
Erase Callback Phone Number #RDNxx
This command erases the single phone number specified by
xx
(0 through 29).
6.5 Remote Configuration/Callback Security S-Registers
The following S-Registers are used with Remote Configuration and Callback Security features.
Remote Configuration Character (S13)
S13 defines the modem’s remote configuration escape character. When the S13 character is entered
three consecutive times from a remotely connected site, your modem responds to it with its Remote
Configuration procedure.
Units: ASCII
Range: 0-127
Default: 37 (
% sign
)
Callback Time Delay (S15)
S15 defines the time delay for Callback attempts after initial passwords have been exchanged
between modems.
Unit: Seconds
Range: 10-255
Default: 20
Callback Attempts (S16)
S16 defines the number of Callback attempts after initial passwords have been exchanged between
modems.
Unit: 1 Attempt
Range: 1-255
Default: 4
Failed Password Attempts (S26)
S26 counts the number of times there has been a failed password attempt. For example, if you
entered
ATS26?
the message
003
would be displayed, meaning someone has failed three times to
gain access to your modem using its password security system.
Units: 1 failed attempt
Range: 0-255
Default: 0
- BA-Series 1
- Intelligent Data/Fax Modem 1
- User Guide 1
- Contents 3
- 1.1 Introduction 6
- 1.2 How To Use This Manual 6
- 1.3 Modem Features 7
- 1.3.1 2834 Series Features 8
- 1.4 Fax Features 8
- 1.5 Technical Specifications 9
- 1.6 Power 10
- 1.7 Modem LED Indicators 11
- 1.8 Controls on PC Board 12
- 2.2 Installation 14
- 2.2.1 Safety Warnings 15
- 2.2.2 Installation Procedure 15
- EIA RS232C 16
- 3.1 Introduction 18
- 3.2 Configuring Your Software 18
- 3.4 PC Initialization Strings 18
- 3.4.2 Other Parameters 19
- 3.5.2 Terminal Emulation 20
- 3.5.3 File Transfer Protocols 20
- Chapter 4 - Command Mode 21
- 4.1 Introduction 22
- 4.1.1 AT Command Editing 22
- 4.1.2 Functional Modes 22
- 4.2 Summary of AT Commands 23
- 4.3 Result Codes 26
- 4.4 Dialing Commands 27
- 4.4.1 Dialing Action Commands 27
- 4.4.2 Dial Modifier Commands 28
- 1028806127853500$123456789 30
- Number Linking NN 31
- Modem Reset Z 32
- Unix UUCP Spoofing $SP 32
- Bell/V.21 Tone B 35
- Auto Speed Detect #A 36
- Carrier Detect Control &C 36
- CTS Control &R 37
- Data Set Ready Control &S 37
- Normal Mode &E0 38
- Auto-Reliable Mode &E1 38
- Reliable Mode &E2 38
- V.42 Mode Select #L 38
- Auto-Reliable Buffering $A 39
- 4.4.9 Flow Control Commands 40
- Hardware Flow Control &E4 41
- Xon/Xoff Flow Control &E5 41
- Xon/Xoff Pass-Through &E7 41
- Send Xon/Xoff Characters #X 42
- Maximum Block Size &BS 42
- Through and Pacing Commands 43
- Speed Conversion $BA 44
- Modem Baud Rate $MB 44
- Serial Port Baud Rate $SB 45
- Off Hook H 47
- BREAK AT<CR> 47
- Force Answer Mode A 47
- 4.4.13 Line Probe Commands 48
- Chapter 5 - S-Registers 49
- 5.1 Introduction 50
- &S 53
- (2834 Series only) 55
- Remote Configuration 57
- 6.1 Introduction 58
- Configuration 58
- Change LOGIN Password #I 62
- Local Inactivity Timer (S29) 64
- 7.1 Introduction 66
- "UUCP spoofing" 68
- 7.3 Speaker Volume Control 71
- DIP-Switches 72
- DIP Switches #13-14 73
- DIP Switches #15-16 73
- 8.1 Introduction 75
- 8.4 Replacement Parts 77
- 8.5 Technical Support 77
- 8.6 Internet Sites 77
- Appendixes 78
- Upgrade Overview 79
- Programming Complete 81
- Appendix B - Troubleshooting 82
- I Am Losing Data 85
- Password Command Summary 94
- V.25bis Commands 95
- Delayed and Forbidden Numbers 96
- V.25bis Operation 96
- V.25bis Mode AT Commands 97
- V.25bis AT Commands 98
- DTR Dialing ($D) Command 100
- NO CARRIER 101
- 25-PIN DTE 102
- Connector 102
- 25-PIN DCE 102
- FCC Part 15 103
- FCC Part 68 Telecom 103
- Canadian Limitations Notice 104
Powiązane produkty i podręczniki dla Modemy Multi-Tech Systems BA-Series
(43 strony)
(66 strony)Behringer Europower PMP960M manuels
Manuels d'utilisation et guides de l'utilisateur pour Mélangeurs Behringer Europower PMP960M.
Nous fournissons des manuels en pdf 2 Behringer Europower PMP960M à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji