Multi-tech-systems ISIHP-2U Instrukcja Użytkownika Strona 105
- Strona / 155
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
MultiModemISI Hybrid Series, ISIHP-2S/2U/4S/4U/4SD 105
Terminal Adapter AT Commands & S-Registers
ENTER. On the other hand, if you are configuring a communications
program, you typically must insert the carriage return character by adding
^M to the end of the command string.
The TA has three modes of operation: offline command mode (the default
state), online command mode, and data mode. The TA responds to AT
commands only when it is in one of the command modes. After the TA
establishes a connection and goes online in data mode, it interprets any
further characters you enter as data rather than commands and transmits
them to the remote device.
When the TA is in data mode, you can switch it to online command mode by
sending it an escape sequence. The TA responds to two types of escape
sequences: in-band (escape sequence is part of the data stream) and out-of-
band (escape sequence is outside the data stream). The in-band escape
sequence is +++AT<cr>; the out-of-band escape sequence is <break
>AT<cr>. You can change the in-band escape character (+) by changing the
value in register S2. You can send the break signal in the out-of-band escape
sequence only from software, not by pressing SHIFT+BREAK on your
keyboard.
When it detects the escape sequence, the TA enters online command mode,
in which it responds to commands while maintaining the connection with
the remote device.
The TA s command buffer can store 80 characters, including spaces and
other characters used in telephone numbers. If you mistype a command
string, you can edit it by using the backspace key, but only before you press
ENTER. As you type a command string, it appears on your monitor screen,
letting you verify your input as you type it.
AT commands recognized by the ISIHP terminal adapter are listed by
function on the following page. For an alphabetic list of AT commands, see
AT commands in the index. The commands in this chapter are organized by
function. Abbreviated commands are listed on the following page by
function along with a short description and page numbers that refer to a
more detailed description, immediately following this list.
Topic Command Description
Command Implementation, p. 107AT Attention code
Return Command execution
- User Guide 1
- 88311551Revision B 2
- Contents 3
- Introduction 10
- Hardware 11
- Installation 11
- Computer Requirements 12
- Shipping Contents 12
- Safety Warnings 12
- Hardware Installation 13
- ISIHP-2S 14
- ISIHP-2U 14
- ISIHP-4S/4U 14
- LED Indicators 16
- ISIHP-2S LED Indicators 17
- ISIHP-2U LED Indicators 18
- Software 19
- (usually port 3) 22
- To install terminal adapters: 24
- To install modems: 27
- General tab 29
- I/O Addresses and IRQ Codes 32
- NT 3.51/4.0 33
- Windows 95 Installation 34
- Windows 98 Installation 36
- Windows 98 39
- To remove the ISIHP card: 39
- To remove the drivers: 39
- {not applicable to -4SD} 45
- North American Users 49
- International Users 50
- Optional Settings 50
- Software/Driver Installation 51
- ISDN TA Configuration Utility 52
- ConfigMenu Menus 59
- Terminal Adapter AT Commands 59
- {2S/2U models only} 61
- Removing the Driver (Novell) 61
- MultiTech Installation Script 63
- To install the Linux driver: 68
- Miscellaneous: 69
- Warranty & Service 71
- Information 71
- Limited Warranty 72
- Command Structure 75
- Command Editing 75
- Dialing Commands 79
- Dial Modifier Commands 79
- Phone Number Memory Commands 80
- Online Connection Commands 84
- RS-232 Interface Commands 86
- Immediate Action Commands 89
- Flow Control Commands 90
- Escape Sequences 92
- Modem S-Registers 94
- Examples of Assigning Values 100
- Examples of Reading Values 100
- Modem Result Codes 101
- Entering AT Commands 104
- Topic Command Description 105
- Command Implementation 108
- Switch Configuration Commands 108
- Data Call Commands 125
- Terminal Adapter S-Registers 126
- Terminal Adapter Result Codes 135
- Modes of Operation 136
- Offline Command Mode 136
- Data Mode 137
- Online Command Mode 137
- Making a Call 137
- Answering a Call 138
- Answering Using Call Steering 139
- Hanging Up 139
- Troubleshooting 141
- Data is being lost 146
- There are 146
- Regulatory Information 147
- FCC Part 68 Telecom 148
- Industry Canada 150
- FCC Fax Warning 150
- Canadian Limitations Notice 151
Powiązane produkty i podręczniki dla Sprzęt komputerowy Multi-tech-systems ISIHP-2U
(114 strony)
(232 strony)Behringer Europower PMP960M manuels
Manuels d'utilisation et guides de l'utilisateur pour Mélangeurs Behringer Europower PMP960M.
Nous fournissons des manuels en pdf 2 Behringer Europower PMP960M à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji