Multi-tech-systems ISIHP-2U Instrukcja Użytkownika Strona 120
- Strona / 155
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
120 MultiModemISI Hybrid Series, ISIHP-2S/2U/4S/4U/4SD
Terminal Adapter AT Commands & S-Registers
#Xn Send Single/Multiple Xoff Characters
Values: n = 0 or 1
Default: #X0
Allows the TA to send either a single or multiple Xoff characters to exert
flow control to the terminal. The #X0 command (factory default setting)
causes one Xoff to be sent until the TAs buffer reaches the Xon level. The
#X1 command causes an Xoff to be sent for every character received after
the TA reaches its buffer full level.
#X0 One Xoff character sent until the buffer
reaches the Xon level (default)
#X1 Multiple Xoff characters sent for every
character received after buffer reaches the
full level.
&Fn Load Quick Setup Profile
Values: n = 0-4
Default: &F0
For quick setup, the TA includes Quick Setup Profiles. Each contains
configuration parameters for a specific type of port operation. To load a
Quick Setup Profile into active memory use the command &Fn, where n is
the number of the profile you want to load. You then can customize the
profile and store it with the &W command, so it loads automatically on
power-up or reset. These profiles are stored in permanent memory and are
not user-configurable.
&F0 Profile 0 Modem-like async operation
(default)
&F1 Profile 1 V.110 async operation
&F2 Profile 2 V.120 async operation
&F3 Profile 3 X.75 async operation
&F4 Profile 4 PPP async operation
&Rn CTS Control
Values: n = 0, 1, or 2
Default: &R1 (CTS forced high)
- User Guide 1
- 88311551Revision B 2
- Contents 3
- Introduction 10
- Hardware 11
- Installation 11
- Computer Requirements 12
- Shipping Contents 12
- Safety Warnings 12
- Hardware Installation 13
- ISIHP-2S 14
- ISIHP-2U 14
- ISIHP-4S/4U 14
- LED Indicators 16
- ISIHP-2S LED Indicators 17
- ISIHP-2U LED Indicators 18
- Software 19
- (usually port 3) 22
- To install terminal adapters: 24
- To install modems: 27
- General tab 29
- I/O Addresses and IRQ Codes 32
- NT 3.51/4.0 33
- Windows 95 Installation 34
- Windows 98 Installation 36
- Windows 98 39
- To remove the ISIHP card: 39
- To remove the drivers: 39
- {not applicable to -4SD} 45
- North American Users 49
- International Users 50
- Optional Settings 50
- Software/Driver Installation 51
- ISDN TA Configuration Utility 52
- ConfigMenu Menus 59
- Terminal Adapter AT Commands 59
- {2S/2U models only} 61
- Removing the Driver (Novell) 61
- MultiTech Installation Script 63
- To install the Linux driver: 68
- Miscellaneous: 69
- Warranty & Service 71
- Information 71
- Limited Warranty 72
- Command Structure 75
- Command Editing 75
- Dialing Commands 79
- Dial Modifier Commands 79
- Phone Number Memory Commands 80
- Online Connection Commands 84
- RS-232 Interface Commands 86
- Immediate Action Commands 89
- Flow Control Commands 90
- Escape Sequences 92
- Modem S-Registers 94
- Examples of Assigning Values 100
- Examples of Reading Values 100
- Modem Result Codes 101
- Entering AT Commands 104
- Topic Command Description 105
- Command Implementation 108
- Switch Configuration Commands 108
- Data Call Commands 125
- Terminal Adapter S-Registers 126
- Terminal Adapter Result Codes 135
- Modes of Operation 136
- Offline Command Mode 136
- Data Mode 137
- Online Command Mode 137
- Making a Call 137
- Answering a Call 138
- Answering Using Call Steering 139
- Hanging Up 139
- Troubleshooting 141
- Data is being lost 146
- There are 146
- Regulatory Information 147
- FCC Part 68 Telecom 148
- Industry Canada 150
- FCC Fax Warning 150
- Canadian Limitations Notice 151
Powiązane produkty i podręczniki dla Sprzęt komputerowy Multi-tech-systems ISIHP-2U
(114 strony)
(232 strony)Behringer Europower PMP960M manuels
Manuels d'utilisation et guides de l'utilisateur pour Mélangeurs Behringer Europower PMP960M.
Nous fournissons des manuels en pdf 2 Behringer Europower PMP960M à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji